Viser av varer
398,-
The Wing Clipper is a must have tool if you are making Flying Geese units for your quilt. This tool, and the associated Fast Flying Geese construction technique, allow you to make four finished units from five squares. The best part is that each unit is constructed slightly oversized so each can be trimmed to a perfect size with perfect seam placement once the sewing and pressing are complete by using the Wing Clipper tool.
398,-
An in between tool that trims down Flying Geese units in 9 additional size not covered with the Wing Clipper 1. Many of today’s best designers like to create quilts and patterns with Flying Geese units that are based on finished heights of ¼” and ¾” increments. They are sometimes just the right size for a particular design and having a tool that gives you the opportunity to make them quickly, and then clean them up with high precision, is a welcome addition to many quilter’s tool box. By supplementing the Wing Clipper 1 with this tool, you will have 19 different size options for traditional Flying Geese units. Absolutely the best set of tools on the market!
475,-
Finally, a tool and technique that will give you high success adding fabric corners to basic shapes. For years we’ve been layering small squares on big squares, marking & stitching on a diagonal line, then hoping everything lines up when we fold the small corner section back into place. If you’ve tried it, you know the pitfalls: too big, too short, too crooked and way too wasteful. No more. With your new Corner Pop tool, you will be able to trim rather than mark, add an oversized replacement triangle and then square everything to a perfect size. In twenty two different sizes - whole, half and quarter inches. Increased success without undue stress for every level of quilter. What’s not to love!
475,-
The Corner Pop II, like our original Corner Pop, allows you to add a “pop” of color to any 90 degree corner. The “pop” with this tool will be twice as tall as it is wide, providing a much “spikier” look, and even more design possibilities! 21 size options from 1” to 12” finished; right and left handed instructions included.
475,-
The Corner Pop III, like our original Corner Pop, allows you to add a “pop” of color to any 90 degree corner. The “pop” with this tool will be three times as tall as it is wide, providing a much “spikier” look, and even more design possibilities! 21 size options from 1” to 12” finished; right and left handed instructions included.
398,-
This tool creates a fundamental unit that is sure to add sparkle to your quilt block designs. Although the ruler shape is similar to the V Block, the final unit has two seamlines radiating from a single corner, so the center triangle in the finished unit resembles a beam of light shining out of that corner. Accurate construction has always been challenging until now. With the Corner Beam tool, all the shapes are cut slightly over sized and once sewn, trimmed to extremely precise units with seams perfectly placed for a crisp sharp point every time. Brighten up your blocks by adding Corner Beam to your toolbox today!
475,-
Now you can make those tough elongated diamond units needed for any Storm at Sea project with ease and success. But remember, this is a basic unit that can combine with any of the other fundamental units to create many, many other interesting designs and quilt projects. You'll precision cut the center diamond, then sew on side triangles to create an oversized unit that you'll trim down to the perfect size.
898,-
We know many of you have been looking for a larger Square Squared tool to make big Diamond Square units for your modern quilts or for framing your beautiful embroidery. But what would you say if we told you could also use it to make Stacked Squares (like in Storm at Sea), Pineapple Blocks, Snail’s Trail Blocks, and a fancy version of a Flying Goose we’re calling Birds of Paradise? With all this, we know you’re itching to give it a try! This big, versatile, two piece tool set comes with the basic instructions for making Diamond Square units that finish from 1” up to 12” in whole inch increments. Y
398,-
Finally a tool that simplifies the construction of the Diamond Square unit without having to use paper foundation piecing. The Square Squared (Square2) is an all-in-one tool that gives you a window template for accurately cutting the center square, a chart printed right on the ruler for the recommended size to cut the triangles sewn to the four sides of the center square and a trim down section on the ruler that simplifies the alignment of ruler to fabric unit and allows everyone to clean up the unit to a precise measurement every time. You can see the tool demonstrated on our free online video demonstration (see below, also on YouTube). This unit is a tricky one to get accurate, but with the Square Squared tool and technique of oversizing and trimming down you’ll have far better success than with any other product on the market.
379,-
The Tucker Trimmer tool was designed to help quilter’s quickly and easily trim down units that are made with triangles: half square triangle squares, quarter square triangle squares (hourglass units), and combinations of half square and quarter square triangle squares (combination units). It has multiple diagonals which allow you to align ruler guide lines with unit seam lines to quickly locate the exact center of pieced units. This makes trim down easy,precise, and perfect every time. No more figuring, or guessing, or struggling to find a center point, and you can see it demonstrated on our free online video demo. I use it for much more than just trimming however and consider it my “must have” tool every time I head to my cutting table.
379,-
An “in between” version of the original Tucker Trimmer I tool, this handy ruler allows you to do all of the same functions as the first except that the sizes of the units are in ¼” or ¾” increments. Although these particular sizes are not nearly as popular as the ½” and whole inch increments available on the Tucker Trimmer I, they are sometimes part of your quilting projects. And if you’ve ever tried to trim down a 2¾” hourglass unit you will highly appreciate this tool. The diagonal guidelines on the Tucker Trimmer II will cross precisely at the center of a 2¾” unit so finding the center is a breeze. A great supplemental tool to have in your ruler collection.